Jiangsu Aoguang Corrugated Pipe Co.,Ltd
Address:Shuguang industrial park jiangyan taizhou city jiangsu province China
The bearing is used to support the parts, but also to support the shaft on the rotation of the parts, the type of bearing friction properties: a sliding bearing and rolling bearings; according to the direction of load points: a radial bearing, to promote the bearing, Bearings and so on.
1, the assembly of sliding bearings
Sliding bearing is a sliding friction bearing, characterized by smooth work, reliable noise, can withstand heavy loads and greater impact load, according to the different forms of structure can be divided into integral, split and tile and so on.
(1) assembly of integral plain bearings
The overall type of sliding bearings commonly known as sleeve, sliding bearings is the most simple form, the main use of pressure and hammer method to assemble, special occasions using hot-loading method, most of the sleeve is made of copper or cast iron, Should be careful, can be used wood hammer or hammer pad wood block hit the way of assembly, the size of the larger tolerance when the pressure with a press press. Whether the knock or press must be prevented from tilting, after assembly, the oil groove and oil hole should be in the required position.
After assembly of the deformation of the bearing, should be trimmed hole, the smaller the available reamer cut, the larger size is used to scraping. At the same time pay attention to control the gap with the shaft in the tolerance range, in order to prevent the rotation of the sleeve work, the sleeve and the box on the contact surface with locating pin or riding screws. As the box and the sleeve material hardness is not the same as drilling, it is easy to bias the side of the soft material, the solution: First, before drilling with a hard material punching the side of the punch, the second is to use a short drill to increase the drill Hole when the drill bit steel.
(2) the assembly of split bearings
Split-type bearings, also known as off the bearing, with a simple structure, easy adjustment and disassembly characteristics, in the bearing pad with two bearings, in the joint with a gasket to adjust a reasonable gap.
① bearing and bearing body assembly
The contact between the upper and lower bearings and the bearing body must be good, if not meet the requirements of thick-walled bearing bearing the hole as a benchmark, scraping the back of the bearing, while the bearing should be close to the ends of the bearing at both ends. Thin-walled tile as long as the bearing in the sub-face than the bearing body in the sub-surface can be more than 0.1mm or so, do not scratch.
② bearing installed in the bearing body, whether radial or axial are not allowed to have a displacement, usually with the end of the pad to stop the positioning or positioning pin positioning.
③ bearing with scraping
The open pad is generally used with its matching shaft research points, are generally first scraping the bearing pad, and then scraping the bearing pad, in order to improve efficiency in the scraping of the bearing pad can not be installed when the bearing tile and cover, the current bearing contact point basic Meet the requirements, and then the upper bearing and the cover on the compression, and scraping on the bearing pad, the further correction of the next bearing contact point. The degree of tightness of the shaft can be adjusted by changing the thickness of the shroud. When the bearing cap is tightened, the shaft can be easily rotated without a clear clearance, and the contact point meets the requirements.
④ bearing clearance measurement
The size of the bearing clearance can be adjusted by the gasket at the middle face, or by the direct scratch pad. Measuring the bearing clearance is usually used to lead the lead method, take a few paragraphs larger than the bearing gap lead wire, on the journal and the middle surface, and then tighten the nut to make the middle face pressed, and then unscrew the nut, remove the bearing cover, Remove the flattened lead wire, each take a section to measure the thickness of the micrometer, according to the average thickness of the lead wire can know the bearing clearance. General bearing clearance should be shaft diameter of 1.5 ‰ -2.5 ‰ (mm), a larger diameter to take a smaller gap value. If the shaft diameter is 60mm bearing clearance should be between 0.09-0.15mm.
- Damper For A Brief Introduction
- Compensator Simple Overview
- Compensator Selection Techniques
- On The Question Of Selection Of Com...
- Compensator For Reliable Research
- Compensator Durability Test
- Main Functions Of The Expansion Joint
- Expansion Joint Structure
- Overall Design Of Expansion Joint
- Control Points Of Expansion Joints
- Damper Proper Operation Is Also Imp...
- Expansion Joint Can Be Better To Ac...
- Expansion Joint More Areas Of Appli...
- Bearing The Importance Of Life And ...
- BBD Blast Furnace Dehumidifier Impr...
- Application Of Metal Hose